Home :: Engine Parts :: Rotax Max Parts :: Clutch & Sprocket - OLD

Clutch & Sprocket - OLD

Disclaimer: Fastech-Racing, Inc. is not an "Authorized" Rotax dealer or Service Center. There is no express or implied warranty direct from Rotax. Any defective part normally warranted through Rotax is covered by Fastech-Racing, Inc.

All parts are OEM Rotax unless otherwise noted.

All parts are OEM Rotax unless otherwise noted.

Products

Rotax OLD STYLE Complete Rebuild Kit (shoes, clutch support and spring/hardware)
3 shoes, clutch support and repair kit included. Not actual picture shown.
$139.95
Qty
#16 Rotax REPAIR KIT CENTRIFUGAL CLUTCH

CONTENT: 3 X CLUTCH SPRING BLACK
3 X ADJUSTING WASHER 10X16X1,2 DIN 988
3 X RETAINING RING 10X1 DIN 471
3 X ADJUSTING WASHER 10X16X1,5

$29.00
Qty
#3 Rotax Clutch Shoe (3 shoes included)
3 shoes included, enough for one clutch assembly.
$95.95
Qty
#4 Rotax CLUTCH SUPPORT 1.5mm
-
$12.95
Qty
#7 Rotax HEX. NUT M20X1,5
-
$3.95
Qty
#8 Rotax THRUST WASHER 15,2/25/1
-
$3.75
Qty
#9 Rotax CLUTCH BUSHING (for 11t Drive ONLY)
FOR SPROCKET WITH 11 TEETH ONLY. Replaces needle bearing that is normally used on 12-16t drive gears.
$8.95
Qty
#9 Rotax CLUTCH NEEDLE CAGE - 2009
FOR SPROCKETS WITH 12 - 16 TEETH. Spec. 2009 Rotax Needle Cage Bearing used in conjunction with the 09' O-Ring to meet Rotax Max Challenge Technical Specifications.
$14.50
Qty
Rotax O-ring for '09 Clutch Bearing
To be used in conjunction with the 09' clutch bearing to meet Rotax Max Challenge Technical Specifications. (NOTE: not shown in diagram)
$1.90
Qty
Rotax Clutch "Roller" Bearing 15x19x20mm (For 12-16t) - Old style
OEM Rotax Clutch "Roller" Bearing 15x19x20mm (For 12-16t). Used WITHOUT o-ring.
$14.50
Qty
#10 Rotax Drive Gears
11-16t available.
$28.95
Select Size & Brand
Qty
#11 Rotax NEEDLE PIN 5X5
#11 Rotax NEEDLE PIN 5X5
$2.50
Qty
#13 Rotax HEX. NUT M28X1 HEIGHT 4,6
TIGHTENING TORQUE 100 NM
$4.90
Qty
#14 Rotax THRUST WASHER 10/19/1,5 (For 11t)
FOR SPROCKET WITH 11 TEETH ONLY
$2.75
Qty
#14 Rotax THRUST WASHER 10/22/1,5 (For 12-16t)
FOR SPROCKETS WITH 12, 13 AND 14 TEETH
$2.75
Qty
#15 Rotax HEX. NUT M10X1 DIN 934
TIGHTENING TORQUE 60 NM
$2.25
Qty
Wildkart Universal Clutch / Flywheel Puller
This Puller will work with both new and old Rotax flywheels. It also fits Comer C-50/K-80/W60 engines. The puller has several hole patterns that fit Leopard & several ICC engines as well. The puller is constructed with steel and has a hardened steel ball at the end of the main bolt to protect the end of the crankshaft. It also comes with an assortment of 12 metric bolts.
$54.95
Qty