Titanium 8x90mm Kingpin (CRG, Tony, etc.) - (Sold Individually)
Fits any kart that uses an 8x90mm kingpin (Measured from bottom of head to end of threads), i.e. Tony Rookie, CRG Mini, etc. High quality, Grade 5, ultra lightweight titanium hardware. 47% lighter than steel, Corrosion resistant, Reduce overall weight. 22 grams.
$17.95
Tie Rod End - 8mm - German (ASK)
Highest quality ASK tie rod end. Made in Germany.
Note: Jam nut not included
Note: Jam nut not included
$15.95
Tie Rod End - 8mm - Japan (IKO), Left
Highest quality IKO tie rod end. Note: Jam nut not included. Made in Japan.
$15.95
Tie Rod End - 8mm - Japan (IKO), Right
Highest quality IKO tie rod end. Note: Jam nut not included. Made in Japan.
$15.95
Tie Rod End - 8mm - Male - Springfix - LEFT
High Quality metric 8mm male tie rod end with maintenance free nylon inserts. Only Left-hand thread available.
$2.95
Stand-Off for Tierod Ends
Allows full movement on the tierod-end, reducing bindage when steering or shifting. Sold individually or by 10-pack.
$1.50
Snipers SA1 Linear Caster/Camber Adjuster
Snipers' new SA1 Linear Caster/Camber Adjuster is the perfect compliment to the V2 & V4 Laser Alignment Systems. The SA1 enables adjustment of camber & caster independently to fine tune your steering geometry when utilizing the V2 or V4 Laser Alignment Systems. Adjust caster in one degree increments while enjoying infinitely adjustable camber settings, both completely independent of the other. Install one pair of SA1's on the top of your spindle mounts for independent caster & camber adjustment or install two pair on the top and bottom of your spindle mounts for maximum adjustability.
$58.00
PKT OTK / Tony Kart Sniper Adjuster Kit - 10mm
NOT RECOMMENDED for KZ/125 karts with front brakes due to clearance issues. Bolt on Sniper Adaptor Kit for OTK Chassis. If you are looking for linear front end adjustments for your chassis look no further. We have engineered a high quality kit that will allow you to bolt on this system at the track. The system includes 2 precision adaptor rings, 2 spherical sockets, 2 spherical washers, 2 king pins & zinc plated hardware to mount the system. The adaptor rings and spherical components are made from high quality stainless steel. When installing this system you will use your existing spindle ride height spacers, lower OTK centralizing or eccentric pill, spacer, king pin nut and safety clip. Includes both the Sniper Adaptor Kit and the Sniper Alignment Kit.
$126.00
Uniball for Steering Shaft - 8mm (IKO, Made in Japan)
8mm uniball for the bottom of steering shaft.
$25.95
Uniball for Steering Shaft -10mm (China)
10mm uniball for the bottom of steering shaft. Fits OTK karts, Tony, FA, Kosmic, etc.
$15.95
Uniball for Steering Shaft -10mm (IKO, Made in Japan)
10mm uniball for the bottom of steering shaft. Fits OTK karts, Tony, FA, Kosmic, etc.
$25.95
Italkart / Intrepid / Praga Spindle Spacer - 25x5mm
Fits 25mm spindles. Sold Individually or by the 10-pack at $2.50 each.
$5.50
Titanium Spindle Spacers - 25x10mm (OTK Style)
OTK Style high quality titanium spindle spacers fit any kart that has 25mm spindles. Sold Individually.
$7.50
Titanium Spindle Spacers - 25x5mm (OTK Style)
OTK Style high quality titanium spindle spacers fit any kart that has 25mm spindles. Sold Individually.
$5.00
Steering Shaft Support w/ Lock
Easily lock down the steering shaft by simply tighening down on the pinch-bolt for front end alignments. Fits 20mm shaft. 31mm overall width.
$18.95
TDC Spindle Spacer Tool (for 25mm spindles)
The T.D.C. Spindle Spacer Tool easily allows you to install wheel spacers into the hard to reach recessed area of the front hub. Works for 25mm spindles only.
$28.95
Righetti 10.5° Spindle - 17mm (SKM, Italkart, Intrepid alternative)
SKM direct replacement aftermarket spindle for older SKM, Alpha, Intrepid, Italkarts, etc. Might require a few additional spindle spacers. Includes 8mm bearings. Sold individually.
$70.00
Wildkart Mini / Cadet Spindle - 17mm (SKM, Italkart, Intrepid alternative)
Aftermarket replacement spindle for older SKM, Alpha, Intrepid, Italkarts, etc. Might require a few additional spindle spacers. Includes 8mm bearings. Sold individually.
$70.00
Italian Motors Fairing Bracket / Data Logger Mount for IAME/Rotax
Mount the Mychron data logger or vent bottle securely to the Italian Motors steel fairing bracket. Incredibly durable! For IAME key ignition and Rotax Max Start & on/off button. Click for dimensions.
$49.95
